If these links do not work for you copy and paste the address below into your email account, put receive or cancel updates in the subject line and press send. This will automatically update your information in our database.

updates@automotivetestsolutions.com

EScope & EScope Pro Download and Installation of latest version - Rev 1.27:

For detailed for instructions on installing the EScope update, click here

WARNING! Due to differences in Win Vista and Win 7, EScope version 1.27 will install to a different location from previous versions. This means you will have to move your saved ScreenJPEGs and Data from the old location to the new location. Installing EScope version 1.27 will not disturb your existing data! It will be up to you to move your files after installing this new version. If you have Windows XP, Windows Vista 32-bit, or Windows 7 32-bit your existing data is located, by default, in c:\Program Files\EScope\Data and c:\Program Files\EScope\ScreenJPEGs. If you have Windows Vista 64-bit or Windows 7 64-bit your old data files will be in c:\Program Files (x86)\EScope\Data and c:\Program Files (x86)\EScope\ScreenJPEGs. The new location is under c:\Automotive Test Solutions\EScope\Data and c:\Automotive Test Solutions\EScope\ScreenJPEGs. Simply copy or move the files in those old locations to the new locations.

(See the step-by-step instructions for moving your old files.)

Quick Start Instructions:

• Download http://www.automotivetestsolutions.com/download/Setup_Escope_1.27.exe(36MB) to your “My Documents” folder.
• Double-click on the downloaded file to install the EScope software. If the installer asks you if it is OK to uninstall the existing version allow it to do so and then run the Setup a second time to install the new update.
• Note that the EScope program will only run if you have your computer connected to Escope hardware with power on unless you run it in Demo Mode.
• You must have the DAQ driver installed to use the Escope, even if running in Demo Mode.
• If you are upgrading from Rev 1.21 or older:
  • When you run the Setup program if the installer doesn't ask to uninstall the EScope allow it to install but then run the setup program a second time to correctly uninstall the old program. Then run it a third time to install the new program.
  • You'll also need to upgrade your driver. See "Driver Download" at the bottom of this page for driver details.

Revision History (most recent version can be downloaded above)

• 02/03/2012: Rev 1.27:
  • Added scaling options for new Rev2 versions of Vacuum and 300 PSI pressure sensors.
  • Replaced old Cam/Crank sensor waveform library with a new bigger and better library of waveforms. The new library has been extended with more cam shaft & crank shaft correlations. Many of these patterns have #1 injector & #1 ignition coil waveforms as well.  
• 3/24/2011: Rev 1.26:
  • Added capability to “Zero” each channel independently (used when working with pressure transducers and ECOP)
  • Added ability to auto adjust window size when increasing for larger screens.
  • Added option to print with grey background on graphs to save ink.
  • Made scope buffer size a variable that can be adjusted on the File/Preferences pop-up.
  • Added ECOP to Range options with the ability to customize the voltage to kV multiplier for ECOP channels.
  • On Tools Menu, if no other tools are found it will say "No Other Tools Installed" instead of saying nothing.
  • Changed the installation directory from “c:\Program Files to” to “c:\Automotive Test Solutions” to keep all ATS programs, settings, and data files in one location that Windows will not prevent access to.
• 12/23/2009: Rev 1.25:
  • Optimized to work better with Windows 7.
  • Added "Size to 1024x574 (Netbooks)" option.
  • Added Panel Close (X).
  • Added error popup for battery low indicator.
  • Added digital input code to read battery low signal.
  • Added process data routine that allows adding offsets to data.
  • Increased Buffer Size.
  • Added "Mark Data (Page Up)" to Deep record.
  • Changed colors of "Mark Cam Shaft" and "Mark Cylinders" to faint yellow and faint green.
• 9/23/2007: Rev 1.24:
  • Added smoothing routine to Measure & Deep Rec.
  • Adding offset to Mark Cylinders for pressure transducer measurements.
  • Modified Deep record save to warn if file saving to already exists.
• 5/24/2007: Rev 1.23:
  • Fixed problem where Demo Mode would automatically get selected at startup or auto-restart if DAQ board was not seen. Pop-up will now allow user to see error and re-start or select demo mode.
  • Changed Mark Cylinders to be offset -25% of one division for pressure marking. This more accurately divides up the cylinders when using the pressure sensor.
  • Added Demo Mode button/indicator to main tab.
  • Added 1MS/s ranges for EScope Pro.
  • Changed default ranges.

4/25/2007: Rev 1.22:

• First version to support both the EScope and EScope Pro. Program will automatically detect and setup for correct hardware at startup.
• Added setup wizard that shows hookup schematics, just-in-time training videos for various sensors, and allows setup file selection form tree of sensor/signal types.
• Added Pressure Sensor Utilities: Automatic scaling for each ATS sensor type, ZERO button, Measure tools for marking cylinders, and +/-5000.0 range setting to cover all sensors.
• Added ? Help buttons and help text tab for quick access to EScope help. Also changed manual to Flash type.
• Changed labels on Timing tab to match labels on scope.
• Added open circuit detection code and indicators that display red borders around CH#s for open circuit.
• Changed custom setup folder to "SetupsCustom" instead of "Setups". “Setups” contains setup files that are not to be changed.
• Added colored text to CH#s on Setup tab.
• Added Right and Left Tab for Window Sizing
• Increased chart history from 5k to 10k

• 5/11/2006: Rev 1.21:
  • First version posted on this update page.

Driver Download (needed if first installation or if upgrading to Rev 1.22 from older version):

• Use the following links to install the the NIDAQ driver.
  • Download http://www.atsnm.com/download/NIDAQ920f1CORE.zip
  • Notes:
    • This driver version supports Windows XP, VISTA and Windows 7 for all EScopes.
• Use the following link to install the NIDAQ driver with MAX if you are having problems the core driver.
  • Download http://www.atsnm.com/download/NIDAQ920f1Config.zip
  • Notes:
    • This driver version supports Windows XP, VISTA and Windows 7 for all EScopes.